磁力微型齒輪泵大家已是很是了解了，對于磁力微型齒輪泵(磁力驅動齒輪泵,不泄漏齒輪泵)以它全密封、無泄漏、耐腐蝕之特點，廣泛用于石油、化工、制藥、電鍍、環保、水處理、影視洗印、國防等部門用來抽送易燃、易爆、有毒與貴重液體，是創建無泄漏、無污染文明車間、文工廠的理想用泵。今天主要為大家介紹磁力微型齒輪泵的安裝過程中要考慮到以下事項：

The magnetic micro gear pump is well known to all. It is widely used in petroleum, chemical, pharmaceutical, electroplating, environmental protection, water treatment, film and television printing, national defense and other departments for pumping flammable and explosive products because of its fully sealed, leak-free and corrosion-resistant characteristics. Toxic and precious liquids are ideal pumps for creating leak-free, pollution-free civilized workshops and cultural factories. Today, we mainly introduce the following considerations in the installation process of magnetic micro-gear pump: 1、將機組放在基礎上，在底板和基礎之間放成對楔墊，通過調整楔墊，找正泵的水平。調好后，擰緊地腳螺栓。

1. Put the unit on the base and set a pair of wedge cushions between the base plate and the base. By adjusting the wedge cushion, the pump level can be corrected. After adjustment, tighten the anchor bolt.

2、在安裝前應對磁力泵和電機進行檢查，各部分應完好無損，磁力泵內應無雜物。

2. Before installation, magnetic pumps and motors should be inspected. All parts should be intact, and there should be no impurities in the magnetic pumps.

3、按基礎尺寸做好混凝土基礎，同時予埋好地腳螺栓。

3. Make the concrete foundation according to the size of the foundation, and bury the foot bolts.

4、磁力泵的吸入、吐出管路應有支架，不能用磁力泵來支承。進出口管路口徑應與泵進出口口徑相統一。

4. The suction and vomiting pipelines of the magnetic pump should have brackets, which can not be supported by the magnetic pump. The diameter of the inlet and outlet pipe should be unified with the diameter of the pump inlet and outlet.

5、安裝完畢，最后用手轉動磁力泵聯軸器，檢查有無擦碰現象，轉動輕松均勻則安裝結束。

5. After installation, the magnetic pump coupling is finally rotated by hand to check whether there is any rubbing phenomenon. When the rotation is easy and even, the installation is completed.

6、磁力泵嚴禁抽取帶有顆粒和易結晶的介質，不允許在關閉排放口的情況下而作連續性運轉，需保持最少的流量。

6. It is strictly forbidden to extract medium with granules and easy crystallization from magnetic pumps. It is not allowed to operate continuously when the discharge outlet is closed. The minimum flow rate should be maintained.

7、為防止雜物進入磁力泵內，在進口處應設過濾器，過濾面積應大于管路截面積的 3 ～ 4 倍。

7. In order to prevent impurities from entering the magnetic pump, filters should be installed at the inlet, and the filter area should be 3-4 times larger than the cross-section area of the pipeline.

8、介質粘度過高時，磁力泵性能、功率均會發生變化，詳細情況請依照說明書操作。

8. When the medium viscosity is too high, the performance and power of the magnetic pump will change. Please follow the instructions for details.

9、必須保證磁力泵的安裝高度符合泵的汽蝕余量，并考慮管路損失及介質溫度。

9. The installation height of the magnetic pump must be guaranteed to meet the cavitation allowance of the pump, and the loss of pipeline and medium temperature should be taken into account.